Manuals and User Guides for Husqvarna Rider 155. We have 3 Husqvarna Rider 155 manuals available for free PDF download: Operator's Manual. Aug 7, 2018 - Husqvarna Lawn Mower. Operator's Manual. 16 Lawn Mower pdf. Rider 155 workshop manualhusqvarna rider 970 workshop manual.
. Oper ator ′ s manual Rider 155 Rider 155 AWD Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h. Removing of the machine hoods.
Checking and adjusting the steering wires.Adjusting the parking brake Rider 155.Adjusting the parking brake Rider 155 AWD.Checking and adjusting of throttle wire.Replacement of fuel filter. Ser vice journal Pre-deliver y service 1 Top up battery with acid and charge for four hours. 2 Fit steering wheel, seat and any optional equipment. 3 Adjust cutting unit: Adjust lift springs (effective weight of cutting unit should be 12-15kg / 26.5-33 lb). Adjust cutting unit so that rear edge is about 2-4 mm / 1/8”. Dear Customer, Thank y ou for choosing a Husqvarna Rider.
Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine.
INTR ODUCTION Good ser vice Husqv arna products are sold all over the world and only through servicing dealers. This is to ensure that you, the customer, get the best support and service. For example, before this machine was delivered it was inspected and adjusted by your dealer. See the certificate in the Service Journal in this manual. KEY T O SYMBOLS Symbols P arking brake These symbols are on the machine and in the instr uctions.
Noise emission to the en vironment according W ARNING! Careless or incorrect use can to the European Community’s Directive. The result in serious or fatal injury to the machine’s emission is specified in chapter operator or others.
KEY T O SYMBOLS Switch off the engine and take off the ignition cable before repairs or maintenance Check the engine’s oil level Check the hydrostat’s oil level Lift up the cutting unit Apply the parking brake. If the engine is cold, use the choke Release the parking brake before driving –. SAFETY INSTRUCTIONS Safety instructions. Look out for the ejector and do not direct it towards anyone. These instructions are for your safety. Read them carefully.
Stop the engine and prevent it from starting before you clean the cutting unit. Insure your Rider. SAFETY INSTRUCTIONS Driving on slopes. Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may regulate the age of the user. Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest. SAFETY INSTRUCTIONS.
Do not try to stabilize the machine by putting your foot on. Never fill the fuel tank indoors. When cleaning the chassis, the machine may never be driven near verges or ditches. Follow the manufacturer’s recommendations regarding wheel weights or counterbalance weights to increase machine stability. SAFETY INSTRUCTIONS. Take care with battery maintenance.
Explosive gases. Reduce the risk of fire by removing grass, leaves and form in the battery. Never perform maintenance on the other debris that may have fastened on the machine. Battery while smoking or in the vicinity of open flames or Allow the machine to cool before putting it in storage. 8 Lock button for parking brake 2 Ignition lock 9 Seat adjustment.
3 Cutting height adjustment lever 10 Lever to disengage the driving front axle, 155 AWD 4 Lifting lever for the cutting unit 11 Fuel cap 5 Speed limiter for reversing. The parking brake lock disengages automatically when the engine, which facilitates starting in the cold. Brake pedal is pressed. Cutting unit Rider 155 and 155 AWD can be equipped with two different cutting units.
Speed limiter The speed of the machine is steplessly regulated with two pedals. The seat has a jointed attachment on the front edge and can intermediate position. Be tipped forward. Release lever Rider 155 AWD Rider 155 AWD has one control for the front axle and one control for the rear axle. Clutch control, rear axle The seat can also be adjusted lengthways.
The control is positioned on the inside of the left front wheel. Rear control (pulled out), drive system disengaged. Front control (pushed in), drive system engaged. Release lever Rider 155.
Pull out the control to disengage the drive system. Move the throttle in between positions 1 and 2. 4 Turn the ignition key to the start position. Start the engine 1 Make sure that the clutch control is depressed. Rider 155 AWD has one control for the front axle and one control for the rear axle. Driving 6 Push the throttle control to full throttle position.
Let the. Connect each end of the red cable to the POSITIVE pole engine run at moderate speed or half throttle for 3-5 (+) on each battery, exercise care not to short circuit any minutes before subjecting it to heavy load. Driving 4 Press in the lock button on the lifting lever and lower the.
When the BioClip function is used, it is very important that cutting unit. The mowing interval is not too long. Do not use the machine on ground that slopes more than 10°. Replace the paper filter annually or every 200 hours. Conducted by authorised service workshop. Only 155 AWD first change after 8 hours X = Described in this operator's manual O = Not described in this operator's manual WARNING!
No service procedures must be. Maintenance Cleaning Front cover Release the clip on the front hood and lift off the fender. Clean the machine directly after use. It is much easier to wash off grass cuttings before they dry.
Oily dirt can be removed using a cold degreasing agent. Right-hand fender Spray on a thin layer. 2 Check the tension of the steering wires by squeezing them together by the arrows as illustrated. It should be 155 AWD possible to push them together so that the distance between them is half as much, without using unnecessary Check that the parking brake is adjusted correctly by placing force. Maintenance Replacing the air filter 2 Pull the throttle wire’s casing as far as possibleto the right and check that the choke is fullyactuated. The exhaust system is hot. Let it cool before starting to replace the air filter.
If the engine seems to lack power or does not run smoothly this may be because the air filter is clogged. Maintenance Ignition system 3 Tap the paper filter against a hard surface to shake off the dust. Do not use compressed air to clean the paper filter. The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. For recommended spark plug, see Technical data. Rider 155 AWD, the engine can not be started if the parking brake is not pressed down.
Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Maintenance Main fuse Open the engine cover. Check that the cooling intake is free from leaves, grass and The main fuse is placed in a detachable holder under the dirt. Battery case’s cover, in front of the battery. Type: Flat pin, 15 A. Check the air duct, located on the inside of the engine cover, ensure it is clean and does not rub against the cooling air intake. Maintenance 3 Insert the bolt and secure it with a locking pin.
Rider 155 AWD Removing the cutting unit WARNING! Observe caution to avoid WARNING! Wear protective glasses when trapping your hand.
Dismantling the cutting unit. The spring which tensions up the belt may break and cause personal injury. Maintenance 5 Adjust the unit’s ground pressure by screwing in or out the 4 Tighten the nuts after adjustment. Adjusting screws located behind the front wheels on both 5 On completion of the adjustment the unit’s parallelism sides. The ground pressure should be between 12 and 15 should be re-checked.
2 Remove the front hood by removing the pin. (There are complete instructions on using the service position inside the front hood). Rider 155 AWD 3 Remove the two support wheels from under the front 6 Place a foot on the front edge of the cutting unit near the hood. Maintenance Checking the blades 8 Lift of the drive belt. Then pull out the pin. To achieve the best mowing results it is important that the blades are undamaged and well-sharpened.
Check that the blades’ attachment screws are tight. 9 Pull the frame forwards and refit the pin. IMPORTANT INFORMATION Replacing or sharpening the blades should be conducted by an authorised service workshop. Lubrication Checking the engine’s oil level. 2 Remove the dipstick. Remove the drain plug from the engine’s left side. Check the oil level in the engine when the Rider stands horizontal with the engine switched off.
Open the engine cover. Loosen the dipstick, pull it up and wipe it off. 2 Check that there is oil in the transmission’s oil tank. Rider 155 Fill if necessary with engine oil SAE 10W/30 (class SF–CC). Rider 155 AWD Fill if necessary with engine oil SAE 10W/ 40 (class SF–CC).
The oil and filter should be changed by an authorised service representative, as described in the Workshop Manual. Troubleshooting schedule Problem Procedure Engine does not start There is no fuel in the fuel tank Spark plug defective Faulty spark plug connections or interchanged cables Dirt in the carburettor or fuel line Starter motor does not turn over the engine Starter motor does not turn over the engine Battery flat Bad contact between the cable and battery. Storage Winter storage Guard At the end of the season, or if the machine is going to stand There is a cover to protect your machine during storage or idle for more than 30 days, it should immediately be made transport. Technical data Rider 155 Rider 155 AWD Dimensions Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 880/2,89 880/2,89 Height, mm/ft 1070/3,52 1070/3,52 Operating weight with cutting deck, kg/lb 268-274/591-604 302-308/666-679 Wheel base, mm/ft 855/2,8 855/2,8 Track width, front, mm/ft. Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +00, hereby declares that Husqvarna Rider 155 and Rider 155 AWD from 2005’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVE: of June 22, 1998 ”relating to machinery”. 1150794-26 ´®z+RoJ¶6s¨ ´®z+RoJ¶6s¨ 2007-02-23.
. Operator´s manual Rider 155 Rider 155 AWD Please read these instructions carefully and make sure English you understand them before using the machine. Rider 155 and Rider 155 AWD Contents.
1 Introduction. 2 Driving and transport on public roads. 2 Manufacturing number. 3 Saftey rules. 4 Explanation of symbols and decals. 7 Safety instructions. Introduction Congratulations Thank you for purchasing a Husqvarna ride-on mower.
This machine is built for the greatest efficiency and rapid mowing primarily of large areas. Controls in one place and a hydrostatic transmission regulated by steering controls also contribute to the machine’s performance. Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer, see the certificate in the Service Journal in this operator’s manual.
These instructions are for your safety. Read them carefully. Safe operation practices for ride-on mowers IMPORTANT! This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. General operation 1.
Use extra care in handling gasoline and other fuels. They are flammable and vapours are explosive. A) Use only an approved container. B) Never remove gas cap or add fuel with the engine running. Allow engine to cool before refuelling.
Travel and transport on public roads Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held. Towing of the machine If your machine has a hydrostatic transmission you should only tow it very short distances at low speed. EXPLANATION OF SYMBOLS AND DECALS These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean.
Xxxxxxx xxxx xxxxxxxx xxx x Xxxxx xxxxxx xx. Xx xxxxxxxx xxxxx xxx xx.
Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the. EXPLANATION OF SYMBOLS AND DECALS Placards 8009-442 – English. SAFETY INSTRUCTIONS Safety Instructions These instructions are for your safety.
Read them carefully. This symbol means that important safety instructions need to be emphasized. It concerns your safety. THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. SAFETY INSTRUCTIONS. Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard.
Operate machine only in daylight or good artificial light. SAFETY INSTRUCTIONS Personal Safety Equipment WARNING! When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment.
SAFETY INSTRUCTIONS. Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine. Do not use on steep slopes.
Do not try to stabilize the machine by putting your foot on the ground. SAFETY INSTRUCTIONS Maintenance WARNING!
The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed. Safe Handling of Gasoline To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. SAFETY INSTRUCTIONS General Maintenance. Never operate machine in a closed area. Keep all nuts and bolts tight to be sure the equipment is in safe working condition.
Never tamper with safety devices. Check their proper operation regularly. SAFETY INSTRUCTIONS. Acid in the eyes can cause blindness, contact a doctor immediately. Be careful when servicing the battery. Explosive gases form in the battery.
Never perform maintenance on the battery whe smoking or near open flames or sparks. The battery can explode and cause serious injury/damage.
SAFETY INSTRUCTIONS. Never make adjustments with the engine running.
The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.
Husqvarna 155 Rider Service Manual Manual De Peachtree
The blades are sharp and can cause cuts and gashes. If a spark arrester is used, it should be maintained in effective working order by the operator A spark arrester for the muffler is available through your authorized Husqvarna dealer. Congratulations on your choice of a top quality product which you will enjoy for many years. This operator’s manual describes Rider 155 and Rider 155 AWD.
The machines are equipped with a 15.5 horse power engine from Kohler. Rider 155 AWD also features all wheel drive. The power transmission from the engine is handled Location of the controls Ignition lock. Throttle and Choke lever The engine speed is adjusted with the throttle control, and thereby also the rotation speed of the blades. The control is also used to activate the choke function. When the choke is used the engine receives a richer mixture of fuel and air, which simplifies cold start.
Cutting unit Rider 155 and Rider 155 AWD are equipped with a cutting unit. Combi - 1030 mm/41' See ”Maintenance Checking the Blades” for identification of the cutting unit. Lift lever for the cutting unit The lift lever is used to set the cutting unit in trans- port or cutting position. Lever for adjustment of cutting height With this lever the cutting height can be adjusted to 9 different positions.
Combi, IMPORTANT INFORMATION In order to obtain an even cutting height it is important that the air pressure in all four tires is the same 8,5 psi (0,6 bar). IMPORTANT INFORMATION The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt. Impaired cooling of the engine. Risk of major engine damage. Before starting.
Read the safety instructions and information on the location and function of the controls before starting (see pages 5-14). Warm engine: 4. Set the throttle control midway between position 1 and 2. Turn the ignition key to start position. IMPORTANT INFORMATION Do not run the starter for more than about 10 seconds at a time. If the engine does not start, wait about 60 seconds before trying again. To start an engine with a weak battery WARNING!
Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.
If your battery is too weak to start the engine, it should be recharged. Release the parking brake by pressing down the parking brake pedeal and then releasing it. Carefully press down one of the pedals until the correct speed is reached. To drive forwards: press down pedal (1).
To reverse: press down pedal (2). Push in the lock button on the lift lever and lower down the cutting unit. IMPORTANT INFORMATION The service-life of the drive belts increases considerably if the engine is run at low speed when engaging the blades. For this reason do not increase the throttle until the cutting unit has been lowered to the cutting position. Never drive the machine on ground with a slope of more than 10°. Mow slopes upwards and downwards, never across. Avoid sudden changes in direction.
Operating on hills Read the Safety Instructions “Driving on Slopes” in the “Safety Instructions”. Release lever The release control must be pulled out in order for the Rider to be moved when the engine is shutoff. Pro 155 AWD has one control for the front axle and one control for the rear axle. Pull the controls to their end positions. Do not use an intermediate position. The following is a list of the maintenance which should be conducted on the machine. For the items which are not described in these instructions go to an authorised service workshop.An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation.
Cleaning and washing Clean the machine directly after use. It is much easier to wash off grass cuttings before they dry.
Oily dirt can be removed using a cold degreasing agent. Spray on a thin layer. Rinse at normal water pressure. Do not direct the jet towards electrical components or bearings. Dismantling of the machine hoods Engine hood The engine is accessible for servicing when the engine hood is lifted up. Tilt the seat forward, release the rubber strap under the seat, and tilt the hood backwards.
Front hood Release the clip on the front hood and lift off the hood. Checking and adjustment of the steering wires The steering is controlled by means of wires.
These can in time become slack, which implies that the adjustment of the steering becomes altered. Check and adjust the steering as follows: 1. Dismantle the frame-plate by releasing the screws (two on each side). Adjusting the parking brake The parking brake is adjusted as follows: 1.
Loosen the locking nuts (1). Tension the cable using the adjuster screw (2) until the play in the cable is taken up. Tighten the locking nuts (1). Adjusting the throttle wire If the engine does not respond as it should do when the throttle lever is moved or if the top speed is not reached, the throttle wire may need adjusting. Loosen the clamping screw (by the arrow), and slide the throttle to the choke position. Replacement of the fuel filter Replace the pipe fitted fuel filter every 100 running hours (once per season) or more frequently if it is clogged. Replace the filter as follows: 1.
Fold open the engine cover. Move the hose clips away from the filter. Use a pair of flat pliers. The paper filter may be carefully tapped on a hard surface to remove dust. Do not try to wash or blow it with compressed air. Insert the paper filter and check that it is correct sealed to its seat.
Tighten the paper filter wing nut and install the precleaner over the paper filter. Ignition system The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. For recommended spark plug, see chapter ”Technical data”. IMPORTANT INFORMATION Fitting the wrong spark plug type can damage the engine. Remove the ignition cable shoe and clean around the spark plug.
Remove the spark plug with a 5/8'. Checking the safety system The machin is equipped with a safety system that prevents starting or driving under the following conditions: Rider 155.
The engine should only be possible to start when the cutting unit is in its raised position and the hydrostat pedals are in the neutral position. Main fuse The fuse is located in a loose holder under the battery case cover, in front of the battery. Type: Flat-blade mounting, 15 A. Do not use any other type of fuse when replacing.
A blown fuse indicates that the mounting has burnt off. Before performing any service or adjustment checklist: 1.
Engage the parking brake. Place the Blade-switch in the disengaged position.
Turn ignition switch to “OFF” position and remove the key. Make sure the blades and all moving parts have completely stopped. Checking and adjustment of the cutting unit’s ground pressure To achieve the best cutting results the cutting unit should follow the underlying surface without pres- sing too hard against it. The pressure is adjusted with a screw on each side of the machine. Adjusting the parallelism of the cutting unit 1. Remove the front hood and the right-hand fender, as described on page 21. Undo the nuts on the lift strut.
Screw out (extend) the stay to raise the rear edge of the cover. Screw in (shorten) the stay to lower the rear edge of the cover. Belt replacement on the cutting unit On these cutting units with 'collision-proof' blades, the blades are driven by one V-belt. Do as follows to change the V-belt: 1. Remove the cutting unit, see page 38. Undo the bolt on the lift strut and the two screws on the cover.
Remove the two support wheels from under the front hood. Fit the support wheels on either side of the rear of the cutting unit.
Wear protective glasses when dismantling the cutting unit. The spring which tensions up the belt can go off and cause personal injury. Place a foot on the front edge of the cutting unit near the wheel and raise the front edge of the unit to make it easier to remove the lift strut. Engage the strut in the holder.
Observe caution to avoid trapping your hand. Grasp the front edge of the cutting unit, pull out and raise into the service position. If the cylindrical bolt, which is now holding the cutting unit is removed, the cutting unit can be lifted off. Restoring from service position To leave the service position, reverse the procedures set out in “Placing in the service position”. Removal of BioClip plug (Combi) To change a Combi unit from BioClip function to cutting unit with rear ejection, remove the BioClip plug located under the unit with three screws.
Put the unit in the service position, see 'Placing in the service position'. Check the engine’s oil level Check the oil level in the engine when the Rider stands horizontal with the engine switched off. Fold open the engine cover. Release the dip stick and pull out.
Wipe off the oil and insert again. The dip stick must be fully screwed down. Change of oil filter Replace oil filter every 200 operating hours.
Drain oil first using the plug on the filter base. Remove the old filter using an oil filter tool. Lightly coat rubber gasket with new oil, then install filter by turning it to the right until hand tight.
LUBRICATION Lubricating the belt adjuster The belt adjuster should be lubricated regularly using good quality molybdenum disulphide grease. 1 nipple from the right-hand side under the engine’s lower belt pulley, until grease is forced out. With daily use lubrication should be conducted twice a week. TROUBLE SHOOTING SCHEDULE Problem Engine will not start. Starter does not pull round engine. Engine does not run smoothly. Engine seems to have no power.
Engine overheats. Battery does not charge. Machine vibrates.
Uneven mowing. Procedure. Fuel tank empty.
Winter storage At the end of the season the machine should immediately be put in order for storage, also if it is going to stand idle for more than 30 days. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.
Dimensions Length without cutting unit Width without cutting unit Height Service weight Wheel base Track Front Track Rear Tyre size Tyre pressure, front & rear Max. Gradient Engine Manufacture Power Displacement Fuel Tank volume Oil synthetic Oil volume Start Noise emissions and cutting width Measured noise level Guaranteed noise level. When this product is worn out or no longer used it should be returned to the dealer or other appropriate body for recycling. We reserve the right to change technical specifications without prior notice.
Note that no legal claims are valid on the basis of information in this manual. Use only genuine parts for repairs. Work done Pre-delivery service 1. Top up battery with acid and recharge for four hours. Fit steering wheel, seat and any optional equipment. Adjust cutting unit: Adjust the lifting springs (the “weight” of the cutting unit should be 12-15 kg/26.5-33 lbs).
Only applies to BioClip. Adjust cutting unit so that rear edge is about 2–4 mm/1/8'. SERVICEJOURNAL Date, mileage, stamp, sign Work done – English ´®z+R23¶5L¨. 115 01 81-95 ´®z+R23¶5L¨ 2005W49.