All Nursing Instructors are expected to comply with DH standards of. Or entered into the computerized prescriber order entry (CPOE) except in emergent. February 2016 Computerized Patient Record System (CPRS) V. 1.0 iii Technical Manual Revision History NOTE: The page numbers in the Pages column are hyperlinked in the Word.
. COMPUTERIZED TELESCOPE INSTRUCTION MANUAL. Selecting an Object Slewing to an Object Finding Planets Tour Mode Constellation Tour Direction Buttons Rate Button Setup Procedures Tracking Mode Tracking Rate View Time-Site User Defined Objects Get RA/DEC Go to R.A/Dec Identify Scope Setup Features Setup Time-Site Slew Limits www.celestron.com. COMPUTERIZED TELESCOPE Filter Limits Direction Buttons Utility Features Version Light Control Factory Setting Get Alt-Az Go To Alt-Az Hibernate Sun Menu Scrolling Menu NEXSTAR MENU TREE www.celestron.com.
INTRODUCTION COMPUTERIZED TELESCOPE Congratulations on your purchase of the Celestron NexStar! The NexStar ushers in a whole new generation of computer automated technology. Simple and friendly to use, the NexStar is up and running after locating just three bright objects. It’s the perfect combination of power and portability. COMPUTERIZED TELESCOPE COMPUTERIZED TELESCOPE The NEXSTAR 102GT// Refractor Telescope with Computerized Hand Control 1.
Objective Lens 7. Accessory Tray Objective Lens Accessory Tray 2. Focuser Knob Fork Arm Focuser Knob 3.
Power Outlet 9. Erect Image Diagonal - 45˚.
Loosen the tripod leg extension clamp (locking bolt) located on the side of each leg. Slide the inner portion of each leg down 6” to 8” inches. Adjust the tripod height until the bubble level on the tripod leg is centered. 2-2 FIGURE 2-2 Tighten the tripod locking bolts to hold each leg in place. Tighten the tube clamp knob by hand to secure the tube to the fork arm. See Figure 2-5 FIGURE 2-5 Your NexStar is fully assembled and is ready to attach the accessories.
Turn the focus knob until the image is sharp. Once sharp, turn the knob towards you to focus on an object that is closer than the one you are currently observing. Turn the knob away from you to focus on a more distant object than the one you are currently observing. Secure the StarPointer bracket by tightening the 3.
Secure the StarPointer bracket by tightening the thumb screw on the mounting platform. Thumb screw on the mounting platform. FIGURE 2-8– INSTALLING figure 2-8– iNSTALLiNg STARPOINTER FINDERSCOPE STArPOiNTer fiNDerSCOPe www.celestron.com www.celestron.com. This will make it easier to get an accurate alignment. The StarPointer is now ready to be used. Azimuth Adjustment Knob Protective Battery Alignment Cover FIGURE 2-9 FIGURE 2-10 BATTERY COMPARTMENT STARPOINTER FINDERSCOPE www.celestron.com.
NGC – Many of the brightest deep sky objects from the Revised New General Catalog. Caldwell – A combination of the best NGC and IC objects. Planets – All 8 planets in our Solar System plus the Moon and Sun. Stars – A compiled list of the brightest stars from the SAO catalog. Rate: Instantly changes the rate of speed of the motors when the direction buttons are pressed. RS-232 Jack: Allows use with a computer and software programs for telescope control and to update your NexStar’s firmware via PC.
Www.celestron.com www.celestron.com. “Saved Site”.
The bottom line of the LCD will display either the current time or the time when you last used the telescope. Since this is your first time using the NexStar, press UNDO to enter current time/site information. Repeat the process for the third alignment star. When the telescope has been aligned to the final stars, the display will read “Match Confirmed”. Press UNDO to display the names of the three bright objects you aligned to, or press ENTER to accept these three objects for alignment. You are now ready to find your first object. Use Up and Down buttons (6 and 9 on the keypad) to scroll to the desired star and then press ENTER.
Use the arrow buttons to slew the telescope to the star you selected. Center the star in the finderscope and press ENTER. Finally, center the star in the eyepiece and press ALIGN. Stars that are at least 40º to 60º apart from each other will give you a more accurate alignment than stars that are close to each other. Once the second star alignment is completed properly, the display will read Align Successful, and you should hear the tracking motors turn-on and begin to track. Press ENTER when cENTERed. Then, center the object in the eyepiece and press ALIGN.
Once in position, the NexStar will model the sky based on this information and display ALIGN SUCCESSFUL. It is usually best to replace the star closest to the new object. This will space out your alignment stars across the sky. If you have used one of the single object alignment methods then it is always best to replace the object that is “unassigned” with an actual object. Press ALIGN to make the change. Object information can be obtained without having to do a star alignment. After the telescope is powered on, pressing any of the catalog keys allows you to scroll through object lists or enter catalog numbers and view the information about the object as described above.
(up and down) and azimuth (left and right). The telescope can be controlled at nine different speed rates. 1 = 2x 6 =.5º / sec 2 = 4x 7 = 1º / sec 3 = 8x 8 = 2º / sec 4 = 16x 9 = 4º / sec 5 = 32x www.celestron.com.
Cpoe Instructors Manual
Note: The EQ North and EQ South tracking modes are only needed with telescopes that can be polar aligned. The NexStar GT series are exclusively Alt-Az mounted telescopes and do not require equatorial tracking.
DEC: by entering the R.A. And declination for that object. Scroll to the “ENTER RA-DEC” command and press ENTER. The display will then ask you to enter first the R.A. And then the declination of the desired object. Press ENTER to slew to the bright alignment star.
Use the direction buttons to carefully center the alignment star in the eyepiece. Press ENTER to slew to the desired object. (left and right) or Altitude buttons (up and down) and press ENTER. Pressing ENTER again will reverse the direction of the Hand Control buttons from their current state. Direction Buttons will only change the eyepiece rates (rate 1-6) and will not affect the slew rates (rate 7-9). This menu allows you to change the rate of speed that the text scrolls across the Hand Control display.
Press the UP (number 6) button to increase the speed of the text. Press the DOWN (number 9) button to decrease the speed of the text. SAVED SITE SAVE SKY OBJ ENTER IF OK SAVE DB OBJ UNDO TO EDIT ENTER RA & DEC SELECT OBJECT SAVE LAND OBJ CENTER OBJECT GO TO LAND OBJ GET RA-DEC GOTO RA-DEC IDENTIFY SELECT CATALOG PRECISE GO TO www.celestron.com www.celestron.com. COMPUTERIZED TELESCOPE 2835 Columbia Street Torrance, CA 90503 TEL (310) 328-9560 FAX (310) 212-5835 www.celestron.com Copyright 2011 Celestron All rights reserved.
22093 (Products or instructions may change without notice or obligation.) 06-11 This device complies with Part 15 of the FCC Rule.
Book Descriptions: Cpoe instructors manual is good choice for you that looking for nice reading experience. We hope you glad to visit our website. Please read our description and our privacy and policy page. How it works:. 1. Register a free 1 month Trial Account. Download as many books as you like (Personal use).
3. Cancel the membership at any time if not satisfied. Note: We cannot guarantee that every book is in the library. But if You are still not sure with the service, you can choose FREE Trial service. You can cancel anytime.
You can also find customer support email or phone in the next page and ask more details about availability of this book. Click 'CONTINUE' button to proceed.